![]() |
#11
|
||||
|
||||
![]()
Howie
I knew I had seen the Coltrane's with Ongaku at RMAF '10. See post #104 in this thread http://www.audioaficionado.org/event...2010-a-11.html Jim
__________________
Jim AMP's: ![]() Pre-amp: D'Agostino Momentum HD Digital:dCS Vivaldi APEX DAC, Clock & Upsampler Analog:SME 20/3 , Esoteric E-03, Benz Ruby Speakers: Wilson Alexandria X2 Series 2 Cables: Transparent Opus Speaker & Interconnects & Power Cords Cables on Digital Shunyata Shunyata Everest Power Conditioner |
#12
|
||||
|
||||
![]() Quote:
![]() |
#13
|
||||
|
||||
![]()
You should pick gear to compliment your speakers, not the other way around...
__________________
2CH: W4S DAC-2, W4S STP-SE, W4S SX-500, Custom ScanSpeak/SEAS Towers, Hot Rodded Rega TT and Jolida JD9 Phono Pre, Asynch PC Transport, WireWorld Gold Eclipse 6 XLR HT: Marantz AV7005, W4S Mini MC-5, Custom Waveguide Towers, SVSPB12-Plus/2 |
#14
|
||||
|
||||
![]() Quote:
Especially for those who have decided to go the SET way, there is no way you can just find a SET to suit any speaker. The decision to go SET means you will have to accommodate your amp by finding an appropriate speaker. I don't think there is a right or wrong here. Having a 27 watt amp does limit my choices of speaker but the SET magic is a big draw to so I am willing to compromise a little! Just my 2 cents! ![]() howie |
#15
|
||||
|
||||
![]()
Howie...what is the Coltrane's sensitivity and how benign is its impedance curve?
|
#16
|
||||
|
||||
![]() Quote:
![]()
__________________
2CH: W4S DAC-2, W4S STP-SE, W4S SX-500, Custom ScanSpeak/SEAS Towers, Hot Rodded Rega TT and Jolida JD9 Phono Pre, Asynch PC Transport, WireWorld Gold Eclipse 6 XLR HT: Marantz AV7005, W4S Mini MC-5, Custom Waveguide Towers, SVSPB12-Plus/2 |
#17
|
||||
|
||||
![]()
Thanks Mike. Yeesh...I am not sure this is such a great pairing with the Ongaku amp. A good portion of the low frequency portion of the pass band well below 4 ohms. Howie, have you tested the two together?
![]() |
#18
|
||||
|
||||
![]() Quote:
I am actually looking more at the Coltrane II which is nominal 8 ohms with a 4.1 ohm minimum if I recall correctly. I have found though, that measurements on paper don't always correspond to real life situations especially with regards to tube amps which can produce thunderous results with what would appear to be an incompatible load. A much more reliable way, in my experience, is to see what real people use with certain speakers or amps or what manufacturers use to demo their products. You can bet your bottom dollar that they won't purposefully compromise their system. The ktema is actually a similar load as the strads but much much easier to drive. Some of the very sensitive speakers i looked into like the JBL DD6600, Tannoy Kingdom Royal are real pigs even with 95db + and 8ohm ratings and you rarely see these speakers with SETs. Don't ask me why but I 'm sure 15 inch woofers play a part! Best way is to demo I guess and make double sure. ![]() |
#19
|
||||
|
||||
![]() Quote:
![]() |
#20
|
||||
|
||||
![]() Quote:
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|
Audio Aficionado Sponsors | |