REL Carbon Special
I took the plunge and ordered 2 RELs Carbon Special :banana:
I plan to follow REL's instructions of hooking these up via High Level Input to each of the MC611s, and XLR LFE input to the 2 Marantz 8805 sub outs. Does any of you have similar hook up in their system with the Carbon Special who can share their insights (Dos / Donts)? I reached out to McIntosh (Chuck Hinton) and he initially recommended to hook up the REL via Low Level RCA inputs to the preamp variable outs and did not recommend using the speaker level connection on MC611. I then sent him the note published by REL on the preferred method of connecting to monoblocs using high level input, and he replied in his email that either approach is ok, and it's up to me to decide. I wonder if anyone of you have first hand experience on either approach, and what is the best way to connect the RELs to the MC611s and 8805A surround processor. Any guidance is much appreciated :thumbsup: Many thanks. |
Quote:
Hi, you'll be very pleased with your new pair! The most important upgrade of our system we made the last years. For stereo, the high level input is preferred. That is what our dealer suggested (and he's REL's favourite dealer of my country). I was surprised that we only had to dial the volume at +/- 25%. I think we ended at about 35-37 Hz. For surround, we went with RCA-cables from our Marantz 8802A sub outs. It's all working very well, you don't hear the subs (until you turn them off!), you just feel them (at high volumes). Good luck! PS. There was only one negative: we had to wait 4 months... |
Excellent choice. I have a single Carbon Special, also connected via high level from my D’Agostino Momentum S250. This is my 6th REL over the years, with a variety of amps, and I’ve always used the high level inputs except for surround use, then low level from the theatre processor.
|
Thank you Tony and Bart.
and thanks for confirming that you are hooking these up via High level cables. I can't wait and hope it will arrive next week. It will be a fantastic Christmas :thumbsup: |
Ditto. 2 different sets of RELs with high level inputs. Not with McIntosh amplifiers, but great results (and super easy to dial in).
|
Awesome. Please give us a full report after they break-in.
|
Thank you all. Will report back once received and dialed in.
|
I’m just trying to learn more about REL. the idea of the 6 pack intrigues me.
So - from what I gather on this thread, you connect REL sub with a small wire that comes off your amp (while your speaker cables also go from the amp to the mains- And then you connect either RCA or XLR from your video processor at the same time? In other words, when listening in two channel, the subs are activated from the high level, but then when watching a movie, they play from the LFE out on your processor? |
Quote:
With amps whose (-) terminal is not at ground, you either leave the ground wire floating or connect it to a chassis ground screw. |
I was looking at REL's. This is the response I go from customer service regarding mono blocks:
"Thank you for your interest in REL. If planning to use a single REL with monoblocks, you must use a low level RCA connection via the preamp instead of high level. If connecting a pair of REL's via high level to the MC2301's, the BLACK wire should be left disconnected from a negative speaker terminal. You would connect the RED and YELLOW wires of each sub to the 8 ohm positive tap on each amp for best output. Please let us know if there is anything else at all that we can assist with, and thank you again for considering our products." |
All times are GMT -4. The time now is 05:14 AM. |
Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
©Copyright 2009-2023 AudioAficionado.org.Privately owned, All Rights Reserved.